What the MOT Emissions Test Actually Measures (and How to Pass It)
- A petrol car passes the basic MOT gas test with carbon monoxide at 0.2% or less, hydrocarbons at 200ppm or less and a lambda reading between 0.97 and 1.03 at fast idle.
- A diesel passes when its smoke reading stays at or under the limit on the manufacturer’s plate, or 0.7m-1 for a car first used on or after 1 January 2014 with no plate figure.
- A lit engine light, a tampered diesel particulate filter or visible smoke from a filter-equipped diesel is a Major fail, and a retest left at the test centre inside 10 working days costs nothing.
Four Gas Readings Clear a Petrol Car and One Smoke Limit Judges a Diesel
A petrol car passes the basic MOT gas test when the tester’s analyser reads carbon monoxide (CO) of 0.2% or less, hydrocarbons (HC) of 200ppm or less and a lambda figure between 0.97 and 1.03 with the engine held at 2,500 to 3,000rpm, then CO of 0.3% or less back at idle. A car that misses those figures is not failed yet: the tester moves to a longer test. A diesel passes when the smoke it makes in a full-throttle burst stays at or under the limit shown on its manufacturer’s plate, or the default limit for its age when the plate gives none.
Two quick checks come first. The tester switches the ignition on and watches the engine management light come on and go off, then holds the engine at about 2,500rpm for about 20 seconds and looks at the tailpipe once it drops back to idle. A light that never goes out or never comes on is a Major fail. So is dense blue or clearly visible black smoke at idle for a continuous 5 seconds.
Every limit here comes from the DVSA’s MOT inspection manual, updated on 14 October 2026, which testers follow. Every fail below is logged as a Major or Dangerous defect, and the MOT fee is capped at £54.85 for a car (about $73, at 1.34 dollars to the pound).
What the Tester Checks Before the Probe Goes In
The engine management light is inspected on cars of a certain age. The tester looks for it on petrol cars with 4 or more wheels and up to 8 passenger seats first used on or after 1 July 2003, and on gas, bi-fuel and diesel cars first used on or after 1 July 2008. Kit cars, amateur-built vehicles and American pickups need no light. A light that is inoperative or shows a malfunction is a Major fail on every other car in those groups, so a lit light is worth diagnosing before the booking, and the guide to why the amber engine warning light fails an MOT covers the usual causes.
The smoke check applies to every vehicle. The tester raises the revs to about 2,500rpm, or to half the maximum engine speed if that is lower, holds them for about 20 seconds and lets the engine settle. Dense blue or clearly visible black smoke fails the car. Some pre-1960 cars are excused where the engine design makes smoke unavoidable, and two-stroke engines fail only if the smoke on acceleration would obscure other road users.
Petrol Cars: Warm Engine, Fast Idle, Then Idle
The gas test covers petrol cars first used on or after 1 August 1975. Hybrids, including mild hybrids, are not gas tested, nor are hydrogen fuel cell vehicles and L category vehicles. The engine has to be hot. The tester reads that from the temperature gauge, the cooling fan cutting in or hot hoses, and revs the engine between 2,000rpm and 3,000rpm until it reaches working temperature if it is cold.
With the engine idling normally and a hydrocarbon hang-up check below 20ppm done, the tester inserts the probe in the exhaust and raises the revs to between 2,500rpm and 3,000rpm. The analyser records CO, HC and lambda. The engine then drops back to idle, between 450rpm and 1,500rpm, and the tester records CO again. To pass the basic test, all four limits must hold: CO up to 0.2% and HC up to 200ppm at fast idle, lambda between 0.97 and 1.03 at fast idle, and CO up to 0.3% at idle.
A reading has to stay over a limit constantly for at least 5 seconds before the car fails. Missing the basic limits does not end the test. The tester enters the car’s details and follows the DVSA flowcharts to a longer test. Where the make, model, engine code, engine size or VIN find an exact match in the database, the tester uses the lesser of that car’s own limits and the default limits. With no exact match, default limits apply.
Older cars are tested at idle with the engine warm, the choke off and no heavy electrical load such as heated seats or a heated rear window. A car that passes on CO but fails on HC at idle gets a second reading at a high idle of about 2,000rpm, and 1,200ppm or less passes both.
Cars with two tailpipes from the manifold have the two readings averaged. One pipe at 0.3% CO and 200ppm HC and the other at 0.1% CO and 150ppm HC averages 0.2% CO and 175ppm HC. Readings from a holed exhaust can be wrong, so the tester rechecks emissions once it is repaired.
On a petrol car first used on or after 1 September 2002, original emissions control equipment that is missing, obviously modified or obviously defective is a Major fail. The tester checks what is visible and identifiable, such as the catalytic converter, oxygen sensors and exhaust gas recirculation valve. An air intake or exhaust leak that could change the emissions readings is Major too, as is an engine idling clearly above its normal speed.
Diesel Cars: The Plate Number and the Smoke Meter
Diesels first used on or after 1 January 1980 are tested with an approved smoke meter. Hybrids, including mild hybrids, skip it. Cars first used before 1980 get a visual smoke check only.
The limit comes from the manufacturer’s plate: the VIN plate, or a separate plate or sticker that probably sits in the engine bay. Look for the letters 24 R and a number, usually in a box near the bottom right of the VIN plate. With no plate figure, the default depends on the date of first use: 2.5m-1 for a non-turbocharged engine and 3.0m-1 for a turbocharged one before 1 July 2008, 1.5m-1 for every engine from 1 July 2008 to 31 December 2013, and 0.7m-1 for any engine from 1 January 2014. Some plates show a very low value, as low as 0.01, and the tester adds 0.05 to a plate value before entering it, so 0.01 becomes 0.06 and 0.5 becomes 0.55. The addition prevents incorrect fails from manufacturing tolerances.
The engine must be at least 80 degrees Celsius, or at normal operating temperature if that is lower. The manual says running the engine with the vehicle stationary is not normally enough to warm it to temperature, so arrive after a drive rather than a long idle in the car park. The tester then holds about 2,500rpm, or half the maximum if lower, for 30 seconds to clear the inlet and exhaust, then raises the revs slowly to the maximum to check the governor. Next come quick, continuous presses of the accelerator, each taking the engine to full fuel in under a second, with the smoke level read after each one.
A diesel passes in any of three ways: the first acceleration reads 60% of the limit or less, the mean of the first 3 readings is at or under the limit, or the mean of any 3 consecutive readings is at or under the limit. For a 0.7m-1 limit, the first-burst route needs 0.42m-1 or less. If the first reading is above the limit, the tester runs 2 more accelerations, and if the mean is still above the limit, carries on up to 6 in total. A first burst far above the limit lets the tester stop early, which is a Major fail.
The tester can decline the smoke test if the engine is unsafe to rev: too little oil, oil pressure too low, abnormal engine noise, a tampered governor or a camshaft belt in unsatisfactory condition. A check of the oil level before the appointment removes the first of those. After a smoke fail on a plate value, a retest uses the same plate value.
DPF Cars and the Engine Light: Where Diesels Fail Fast
On a diesel, the tester looks at the visible emission kit: diesel oxidation catalysts, the diesel particulate filter (DPF), exhaust gas recirculation valves and selective catalytic reduction valves. Kit fitted by the maker that is missing, obviously modified or obviously defective is a Major fail. So is any evidence that the DPF has been tampered with. A DPF that has clearly been cut open and rewelded is rejected unless the person presenting the car can show a valid reason, such as filter cleaning.
On a DPF car the tester also checks that no visible smoke comes from the exhaust at the time of the metered test. Visible smoke of any colour is a Major fail. Smoke or vapour of any colour thick enough to obscure other road users’ vision on any diesel is Dangerous.
The engine light works the same way on diesels first used on or after 1 July 2008 as on petrol cars: a light that is off when it should be on, or on when it should be off, is a Major fail. A dashboard warning on a diesel is worth reading against the handbook before the test, and what red and amber warning lights mean shows which ones count at the test station. Fluid leaks have their own rule in the same manual section: a leak that spreads into a pool more than 75mm across within 5 minutes at idle fails, while coolant, screenwash and the fluid used by selective catalytic reduction systems are not reasons for failure.
What a Fail Costs and What You Can Drive Away
The £54.85 cap (about $73) carries no VAT. The MOT test leaves the wear and condition of the engine, clutch and gearbox unchecked. A failed car is listed with Dangerous or Major problems and the driver might not be allowed to drive until they are fixed.
You can drive a failed car away only if the current MOT is still valid and no Dangerous problem was listed. Otherwise the repair comes first. The car must still meet minimum roadworthiness standards at all times. Driving a car that failed over a Dangerous problem carries a fine of up to £2,500 (about $3,350), a driving ban and 3 penalty points.
Leaving the car at the test centre for the repair brings a partial retest, with no fee, if the retest happens within 10 working days. Taking it away and returning inside 10 working days also leads to a partial retest, though a partial fee can be charged. After that, it is a full retest at the full fee. The centre must hand over a printout of a failed emissions result and keep a retrievable record for 3 months. A driver who thinks the result is wrong can appeal it, and the guide to appealing an MOT fail covers the deadline to meet before any repair money is spent.
Want more car content? Add us as a preferred source on Google to your favourites list for the best automotive news and analysis on the internet.
If you enjoyed this article, be sure to follow us on Microsoft Start.
Sources
- DVSA: MOT inspection manual, cars and passenger vehicles, 8. Nuisance
- GOV.UK: Getting an MOT, MOT costs
- GOV.UK: Getting an MOT, MOT test result
- GOV.UK: Getting an MOT, Retest after a repair
Reviewed by Preetam Gadekar