Sachs and LuK Give No Mileage for a Dual Mass Flywheel. They Give Tests
No mileage for a dual mass flywheel appears in any maker document read for this article. Sachs, the clutch brand of ZF, calls the part a wear item with no fixed replacement interval and says to renew it at the latest with every second clutch replacement. Life depends on how the car is driven and loaded, so the answer is a rule and a set of measurements.
Key takeaways:
- Neither the Sachs page nor the LuK documents read here give a mileage for a dual mass flywheel. Both give a replacement rule and tests.
- Sachs says to renew it at the latest with every second clutch replacement. LuK says to check it at every clutch job.
- A rattle alone does not condemn it. LuK reports that a large quantity of flywheels returned for noise prove serviceable.
What the Makers Publish Instead of a Mileage
No Figure in the Documents Workshops Use
Four trade documents were read in full for this article. Schaeffler, which owns the LuK clutch brand, publishes a 52-page brochure on dual mass flywheel technology and failure diagnosis, dated 2019. A LuK diagnosis guide from 2012, a LuK service sheet from 2016 and a ZF sheet from 2018 complete the set, with a Sachs service page read alongside.
None of the five gives a mileage or a number of years for the life of the part. Mileage appears in the brochure only as a question the workshop puts to the customer, alongside towing, taxi use, chip tuning and earlier clutch repairs. The maker’s own checklist treats life as something worked out from use, not read from a table.
Not found means not found in these documents, not that no figure exists. Car maker handbooks were not searched exhaustively and Valeo’s catalogue was not opened. One targeted search of Volkswagen, Ford, Vauxhall and Peugeot material found no flywheel interval, and the DVSA MOT inspection manual landing page lists no flywheel item.
The Rule Sachs Does Give
Sachs answers the question on its flywheel service page, which carries no date. “A dual-mass flywheel is a wear part without a fixed replacement interval.” Driving style and load decide how long it lasts, Sachs says, and the rule follows: “SACHS recommends renewing the dual mass flywheel at the latest with every second clutch replacement.”
The wording sets a ceiling, not a mileage. The second clutch is the latest point Sachs names. Sachs also says the flywheel and clutch wear together and are best replaced as a set, as the gearbox comes out for both jobs. A clutch left slipping can turn a clutch repair into a clutch and flywheel repair.
LuK sets a check in place of a ceiling. Its brochure says to check the flywheel at every clutch replacement and warns: “A worn and defective DMF can damage the newly installed clutch.” For doubtful cases: “If in doubt, always replace the DMF along with the clutch.” No maker figure for clutch life was found, so neither rule converts to miles.
What Shortens Its Life
Low Revs, Stalling and Slow Cranking
Sachs names three things that shorten a flywheel’s life considerably: stalling often, running at very low revs and an engine that runs poorly. LuK lists “Labouring the vehicle in too low a gear” among the driving techniques to investigate.
The part filters the pulses that every firing stroke sends down the drivetrain, and the arc springs between its two masses do that work. LuK’s sheet sets the limit: “The DMF is only designed to eliminate a specific level of vibration from the drive chain, if the vehicle already has a pre-existing vibration issue it will shorten the service life of the DMF.”
Starting is the other load. The ZF service sheet gives about 300 rpm as the cranking speed, the car maker’s own value governing, and says cranking below that value causes excessive vibration: “Over an extended period, the vibrations lead to the failure of the component.” A new battery can hide a worn starter’s slow crank. ZF’s wording is “over an extended period”, so the risk lies in repeated slow starts.
Towing, Tuning and a Slipping Clutch
LuK’s 2016 sheet lists towing, overloading and long spells of air conditioning or heating at idle among the outside causes of early failure. Its verdict on early failure: “Those that do show signs of wear are often found to have failed due to external forces.”
The brochure says chip tuning can raise engine power by up to 30 per cent and that, in many cases, the flywheel’s safety reserve is used up or exceeded, sometimes by more than 30 per cent. LuK says the arc springs can end up fully compressed in normal driving, which spoils noise insulation and can make the car jolt, and that running the springs fully loaded too often can destroy the flywheel. One design, a flange with a built-in friction clutch, is built for short load peaks only, and constant overload from an excessive trailer or tuning wears it early. In extreme cases the flange cannot pass enough torque to drive the car, and LuK says the clutch is often replaced without curing it. That applies to that design only.
A slipping clutch heats the flywheel. Sachs says a discoloured friction surface shows overheating, the result of letting the clutch slip for long, and that prolonged overheating can harden the special lubricant, which “frequently ends in component failure.” A slipping clutch can give off a burning smell. LuK adds that burnt facing residue can work into the arc spring channel, and its remedy is to replace the flywheel.
How a Worn One Is Judged
The Measurements Behind a Replacement Verdict
LuK treats free play as the wear indicator: the angle the two masses turn against each other before the arc springs take load. Free play and rock, the tilt between the masses, are measured with the gearbox off, using LuK tool 400 0080 10, against rated values that vary by flywheel type. A full functional test needs a special test facility. A driver cannot do this at the kerb.
With the gearbox in place, Sachs describes a rough hand check: paint-mark both masses, turn the secondary by hand each way, and look for equal play both ways and a return to rest on its own. More than about 10 mm each way and Sachs recommends replacement. LuK says that on some makes the secondary mass turns several centimetres and stays where it is left, which is permissible. The two describe different designs. The number to trust is the one for that car’s flywheel.
LuK’s limits belong to the part. For a plain bearing, LuK gives a maximum radial clearance of 0.04 mm when new, in relation to the diameter, and an admissible increase over its service life of up to 0.17 mm. Above 0.17 mm it says replace. Normal tilt is up to 1.6 mm with a ball bearing and 2.9 mm with a plain bearing.
Noises That Are Not the Flywheel
LuK’s 2016 sheet says: “A large quantity of Dual Mass Flywheels returned under warranty for “Noise” are subsequently found to be serviceable.” The cause is often a second fault with similar symptoms, such as auxiliary drive vibration, a worn crankshaft damper, bearing wear in the input shaft or gearbox, worn mounts or engine running problems.
ZF’s sheet says noises on starting, driving or switching off are often associated with a flywheel defect, then continues: “However, the noises are actually caused by sources of error in the periphery of the DMF.” On switching off, a stuck or coked exhaust gas recirculation valve, or a blocked shut-off flap, lets the springs compress further. A new flywheel, with lower internal friction, can make these noises more noticeable.
Starting trouble is a separate fault to rule out first, and the sounds at the key turn narrow it down. Sachs notes that a weak battery, the starter, the injection system and the shut-off flap produce the same symptoms. LuK says replacement should follow only an exhaustive inspection.
No maker promises a mileage, so the decision belongs to the clutch job and to measurement. Sachs names the second clutch as the latest point and LuK wants a check at every one, with limits workshops apply with the gearbox out. A rattle at idle or on switching off is where diagnosis starts. A flywheel quoted before the battery, starter and engine are checked has not been diagnosed.
Want more car content? Add us as a preferred source on Google to your favourites list for the best automotive news and analysis on the internet.
If you enjoyed this article, be sure to follow us on Microsoft Start.
Reviewed by Preetam Gadekar