How to Tell If Worn Suspension Will Fail Your MOT (and What Testers Check)
- A shock absorber fails the MOT when it has negligible damping effect or severe leakage, while a slight film of fluid on the body is not a reason for rejection.
- Joints, pins and bushes fail on play (more than 2mm on a 12mm pin, 3mm on a 25mm pin, 10% of the diameter above that), and springs fail when they are fractured, weakened or insecure.
- A Dangerous fail bars you from driving away, with a fine of up to £2,500 (about $3,350), a ban and 3 penalty points for anyone who does.
What Fails the MOT on Suspension and What Only Earns an Advisory
A tester fails a shock absorber that has negligible damping effect or shows severe leakage. A joint, pin or bush fails when play passes a measured limit. A spring fails when it is fractured, seriously weakened or not held securely to the car. Three things do not fail a car: slight seepage that leaves a film of fluid on a shock absorber, a missing bump stop rubber, and a bush that moves a little by design.
The DVSA inspection manual, last updated on 14 October 2026, sorts every suspension fault into one of three categories. Minor is an item to watch, and it appears on the certificate as an advisory. Major is a fail. Dangerous is a fail with a ban on driving the car until it is repaired. Many suspension defects sit at Major, and the ones that reach Dangerous describe a part that is missing, coming loose, fractured or no longer working.
That sorting decides what you do next. The AA’s expert patrol Lee Morley puts the stakes of an advisory like this: “An advisory item highlights a potential issue identified during the MOT test. While it may not be dangerous at the time of inspection, it could deteriorate and become a safety risk if left unchecked. That’s why we recommend addressing advisory items as soon as possible.”
How to Spot a Failing Shock Absorber Before the Tester Does
A shock absorber, also called a damper, turns the motion of a bump into heat through oil forced past a piston. It works with the spring to keep the car level under acceleration, braking and cornering. Halfords puts the working life at 5 to 10 years or about 75,000 miles, and says the figure depends on mileage, driving conditions and damage, with poor roads or heavy loads wearing them out sooner.
Halfords lists six symptoms. Steering wheel vibration that turns up regularly or keeps getting worse is the first. Uneven tyre wear, with patches or flat spots on the tread, is the second. A nose dive when you brake is the third, and it points to front dampers that have lost fluid or weakened. A longer stopping distance is the fourth. A car that feels as if it sways or swerves is the fifth, and a rattle, which can come from a damaged shock absorber or a broken spring, is the sixth.
A walk around the car adds a visual check: look at the body of each damper for fluid. The manual draws a clear line here. Slight seepage that leaves only a film of fluid passes. Severe leakage is a Major fail, as is a damper damaged so that it no longer works, a worn damper bush and a damper with negligible damping effect. A damper that is loose on its mounting is Major, and one that is missing or likely to come off is Dangerous. A missing damper counts only when the car was fitted with one as standard.
The tester judges damping across the whole inspection, and a damper that shows negligible damping effect at any stage of it is a reject. A damper with no visible leak can still fail on damping. Halfords adds that a car which passed its MOT can still need new shock absorbers, and advises a qualified mechanic’s check for anyone who spots the symptoms above.
Replace dampers as a pair, front or rear. Halfords gives the reason as consistent damping, better brake performance and longer tyre life, and notes that some cars carry different dampers at the front and the rear, so match the part to the registration.
Springs, Arms and the Corrosion Hotspots That Fail Cars
Springs get a physical test. The tester jacks the car and lowers it again, and a coil spring that does not seat correctly when the suspension returns to its normal running position is rejected as insecurely attached. That is a Major fail. A spring with fixings so loose that you can see relative movement is Dangerous, as is a fractured main leaf on a leaf spring. A fractured or seriously weakened spring is Major, and so is a missing spring, which becomes Dangerous when directional control is affected.
A rattle is one of the symptoms Halfords ties to a broken spring, and the guide on why a car knocks over speed bumps covers the worn links and bushes behind a knock over bumps.
Welding is a trap. The manual lists welded repairs and excessive heat applied to highly stressed parts as unsafe modifications, and an unsafe modification to a spring or any suspension component is Major. A modification that leaves the suspension inoperative is Dangerous.
Arms, rods, struts, sub-frames and anti-roll bars are the parts where corrosion shows up. Some cars use thin pressed steel for them, with hollow box sections and up-facing surfaces that collect road dirt, salt and other chemicals, which cause severe local corrosion. The manual tells testers to pay special attention to them. A component that is excessively damaged or corroded is Major, and one that is fractured or likely to fail is Dangerous. A missing bump stop rubber, again, is not a failure.
Corrosion near the mountings is judged by the 30cm rule. Any load bearing metal or panelling reaching 30cm out from a sub-frame, spring or suspension mounting sits in what the manual calls a prescribed area. If rust or a poor repair significantly cuts its strength or continuity, the car fails as Major. If the weakening is bad enough that control of the car is likely to suffer, the fail is Dangerous. Cars with gas, air or fluid suspension have their own entries: an obvious leak is Major and an inoperative system is Dangerous. The tester also checks retaining and locking devices on the suspension, and a missing or ineffective one is Major. The manual tells the tester to give the benefit of the doubt when it is unclear whether a locking device is missing or ineffective.
Joints, Bushes and Dust Covers: The 2mm, 3mm and 10% Limits
Play is the measurable part of the test. The tester uses a small pinch bar or wheel play detectors to check spring pins and bushes, and play counts as excessive when it is more than 2mm on a 12mm pin, more than 3mm on a 25mm pin, or more than 10% of the diameter on a pin wider than 25mm. A pin, bush, joint or bearing past those limits is a Major fail. One that is likely to come detached is Dangerous.
Without detectors, the tester jacks the front wheels clear of the ground, levers a bar upwards under each wheel in turn and looks for movement, then rocks and shakes the wheels. On cars where the spring force does not act on the lower arm, the tester grasps each wheel at 3 o’clock and 9 o’clock and pushes and pulls hard. Any movement in a wheel gripped at those two points is what the tester is looking for.
Rubber is judged more gently. The manual says some rubber and synthetic bushes are built to give a high degree of movement, so the tester rejects them only for serious deterioration of the bonding or the flexible material. MacPherson strut top bushes often carry a good deal of sideways play by design when the wheel hangs free, so they are rejected only when wear or poor adjustment causes that play.
The dust cover on a joint shows how a fail develops. A cover that has severely deteriorated is Minor, which means an advisory. A cover that is missing, or no longer keeps dirt out, is Major. The first is a watch item and the second is a fail, so a torn cover is worth fixing while it is still only an advisory.
After a Suspension Fail: Driving Rules, Retests and Fees
GOV.UK lists a car as failed when its result carries a Dangerous or Major problem, and you might not be allowed to drive it until the fault is fixed. You can take a failed car away only when its current MOT is still valid and no Dangerous problem was listed. Otherwise it stays put until it is repaired. Even when you can drive it, the car must stay roadworthy at all times. The AA names suspension among the Major faults, and on dangerous defects Lee Morley says: “We strongly advice against driving a vehicle with a known dangerous defect. By doing so, you are potentially putting yourself and others at unnecessary risk.”
The penalty for ignoring a Dangerous fail is a fine of up to £2,500 (about $3,350), a driving ban and 3 penalty points.
Repair and retest costs depend on where the work happens. Leave the car at the test centre and have it retested within 10 working days, and the partial retest carries no fee. Take it elsewhere and bring it back within 10 working days, and the partial retest can carry a partial fee. After that window the car needs a full retest and the full fee, which is capped at £54.85 (about $73) for a car. If you think the tester got it wrong, the process for challenging a result is set out in the guide on how to appeal an MOT fail.
The practical order is short. Check the dampers for wet streaks, the joint covers for tears and the arms for flaking rust. Book a garage for any symptom on Halfords’ list, and ask for dampers to be replaced in pairs. Treat an advisory on a joint cover or bush as a booking for a repair before next year’s test. Read suspension faults and MOT failures for how often these defects send cars back.
Want more car content? Add us as a preferred source on Google to your favourites list for the best automotive news and analysis on the internet.
If you enjoyed this article, be sure to follow us on Microsoft Start.
Sources
- DVSA via GOV.UK: MOT inspection manual for cars and passenger vehicles, 5. Axles, wheels, tyres and suspension
- GOV.UK: Getting an MOT, MOT test result
- Halfords: What are shock absorbers?
- The AA: Common reasons for an MOT failure and what to do if your car fails
Reviewed by Preetam Gadekar